GTMEDIA Forum

The green is the earlier hardware that has a 3.7v under powered battery.

Buy the black one with the 7.2 volt battery.

Owen

I think the V8 finder Pro has a RS232 port.
viewtopic.php?f=51&t=7535

Using that you should be able to restore it.

Owen

Até o momento eu ainda não consegui configurar uma boa imagem no meu Gtx Combo, a minha tv é uma smart 4k, já tentei 4:2:2, 4:4:4 Rgb, em uma jogo de futebol a imagem parece em camera lenta e sem brilho, já aqui com outro aparelho de outra marca também android 4k é bonita a imagem com brilho nitide...

Vanni wrote: ↑

Mon May 13, 2024 6:59 am

Buongiorno, non è vero, fino a dicembre 2023 la card veniva aggiornata
Grazie

Most PayTV cards receive a data signal via the PayTV set top box each month or even weekly.
The card times out and needs to be placed back into the payTV receiver to wait for the data signal authorizing it again.

Owen

Yes that is the last update.

viewtopic.php?f=71&t=1746

Owen

southernconnectdriver wrote: ↑

Sat May 11, 2024 2:09 pm

I have this bt03 but it's only showing red light and it's not connecting please is there any solution to the power port

Those units will not power on if connected to the charger.
Will not power on if not charged.

Owen

If you mean that you do not see that screen at power on, you may have set a startup app in customize.

I have mine set to DVB app so it boots into the DVB app / TV.

Owen

Normally just press exit twice to return there.

Owen

If you have a multi meter or volt meter, check 12 volts is reaching the main board.

Owen

Does it have any lights on the front panel?

Owen

No idea of what to fix. To avoid this again add earth wires from TV to combo and to the TV antenna ground so any ground currents do not use the HDMI cable. Even a AV cable will help, but then the combo does not have one. I had issues with an electric fence clicking the video and a AV cable stopped i...

It may be a low signal that is just got by your other unit, but is below the sensitivity of your new unit.

Owen

It maybe that your switch does not like the resolution that the boxes are outputting. Have you tried changing the resolution? Your HDMI switch? Has it had a fault that has damaged the UHD and Turbo? I burnt out a HDMI switch by plugging in 12V instead of the 5V it wanted. I now place red tape over t...

I think you can watch a channel on the same TP as you are recording a channel. There is only one satellite receiver, so only one tP can be seen. You should also be able to watch a channel off the DVT-T. A factory reset should return the satellite list, but will remove everything else you have done. ...

If you start on the channel and then go to add BISS key, the correct sid / freq etc will be there.
Then just replace the 16 x zero with the key.

When you press info on a channel at the bottom right there are three numbers with a / between them.
1165/1167/1
VPID / APID / SID

Owen

The best way is to add each satellite to your unit and then blind scan in the channels.

I see satellites from 100.5e to 177w.
My lists would have many satellites and channels you will not see from the north.
Your list will have satellites I do not see from the south.


Owen

Hola Den Son feeds ocasionales. En el menú oculto que trae el deco v8x ....en la opción de keys .... aparece vacío el segmento de keys. Aun así...el deco funciona descifrando y abriendo esos canales, pero no entrega la opción de visualizar aquellas keys descifradas. I thought that if you export the...

Looked at my V8X and can not find any way to see bit rate.

Unless here is some hidden service page, it looks like there is no way.

Owen

Yes I just tested and just the TV picture a black screen is saved. With menu graphics over the picture, as you have found yes just the graphics. There is some error in this or rights protection is stopping the video part from being screen shot. I have been told that Windows PC screen shots has added...

I find it best to have the USALS ku mover on port one of a DiSEqC switch as if a power surge happens the switch reverts to port one.

Remember you can not use a 22kHz switch before USALS or DiSEqC movers. The control pulses are 22kHz, so the 22kHz switch will pulse as well.

Owen

Press and hold the power button.

Then select screen shot.

The pic is then in local disk, pictures/screenshots.

I do not know how you get it out of there?

Owen

You can enter the TP info into the TP list and do a auto (manual) scan, just leave the TP that gets stuck off the list.

Owen

GTCOMBO series usb forced upgrade guide(2022.7.20).zip

Try with another power supply as well.

Owen

I had the same things happening. In the end my SSD failed to even work on my PC. Cheap SSD and I think is got too hot with being slow formatted Some comments online (Aliexpress) suggest the 2Tb SSD I had was a fake and was only 500Mb. I too tested with the copper cover off for a better plug in. The ...