GTMEDIA Forum

juancar2020 wrote: ↑

Sun May 22, 2022 4:38 pm

V8 UHD.
Si configuramos con IP fija, y se apaga el deco, al encenderlo las lineas xxxxx aparecen en stanby y hay que entrar en la configuración y activarlas. Con la última versión de firmware.

juancar2020 wrote: ↑

Sun May 22, 2022 4:38 pm

V8 UHD.
Si configuramos con IP fija, y se apaga el deco, al encenderlo las lineas xxxxx aparecen en stanby y hay que entrar en la configuración y activarlas. Con la última versión de firmware.

GKnight wrote: ↑

Tue May 31, 2022 2:33 pm

Hi, my V8 Turbo with firmware "GTMEDIA_V8TURBO_Release_V303_20211215.zip" has bug with the EPG info when changing channels.

I'm using hispasat 30º and when I'm channel zapping there is some issue with the EPG information because the first 30 seconds or more it shows the wrong EPG info.
For the first seconds minutes it shows EPG info from other channels and it takes some time till it fully updates.

This makes confusion because you never know if it is already updated or not.

I have V7 series box and this issue does not happen.
I have tried factory reset and does not fix.

I hope this can be fix in a new firmware update.
Thanks

Feralkiwi wrote: ↑

Tue May 31, 2022 9:36 pm

I have also noted this.
The program now / next does not show until AFTER the signal is locked.

Question for you?
What switching / motor move do you use?
If you have DiSEqC 1.1 AND 1.0, channel change will be faster if you if you set the option in the antenna settings menu for "DiSEqC 1.1 first", IF you switching has the 1.1 switch first.

If you are using motor move and your channel change needs a motor move, then the program info will not show until after the motor has completed the move and signal is locked.

A over all fix for this would be to have the program, Now / Next, show with out waiting for signal lock.
EPG data is kept in a file and does not need to be collected from the signal stream, unless it is the first time on this channel / TP.

Owen

lungo wrote: ↑

Tue Jun 07, 2022 10:16 am

You can update the V8 UHD receiver, as there is a very annoying bug.
It's that when you make a schedule to record something at a certain time, it never records anything.
I have tried everything, put the same channel that the recording is programmed and it does not record.

lungo wrote: ↑

Tue Jun 07, 2022 10:32 am

I use a USB formatted in FAT32.
And when I do to program something and turn off the receiver then nothing is recorded.

hazman wrote: ↑

Tue Jun 21, 2022 3:41 am

I have a V8 UHD receiver that has a problem when switching from satellite to combo the Terrestrial channels are listed and there is a very good signal reading on all channels but there is no picture just a blank screen showing, If i re scan the pictures come back. Any ideas what is going on to cause this?
This happens every time i switch from sat to combo.
[/quote

To avoid minor problems, a new list should be made, I use the list with version 235 and I am making the new one with version 238, which fixes various errors such as blocking if I disconnected and activated Internet

In order to see the Terrestrial you must disable TS delayer

CAJE wrote: ↑

Tue Jun 21, 2022 8:44 am

hazman wrote: ↑

Tue Jun 21, 2022 3:41 am

I have a V8 UHD receiver that has a problem when switching from satellite to combo the Terrestrial channels are listed and there is a very good signal reading on all channels but there is no picture just a blank screen showing, If i re scan the pictures come back. Any ideas what is going on to cause this?
This happens every time i switch from sat to combo.
[/quote

To avoid minor problems, a new list should be made, I use the list with version 235 and I am making the new one with version 238, which fixes various errors such as blocking if I disconnected and activated Internet

In order to see the Terrestrial you must disable TS delayer

Many thanks CAJE all good now it was the TS delayer