rs 232

V8 NOVA / V8 HONOR / V8 PRO2/V8 UHD / V8X

Moderators: admin, GTMedia Team

Post Reply
gosiadila1234
Posts: 8
Joined: Thu Dec 07, 2017 12:10 pm

rs 232

Post by gosiadila1234 »

BOOTROM ...
UPG...
DDR Calibration Completed
start send upgclient
Start to check serial...
!! UpgClientTest FAIL: Receive failed !!
Please reset the STB!

I do not want to reset the flash, all the correct v625 cables
BOOTROM ...
UPG...
DDR Calibration Completed
Got sync byte!
Start sending client...
not JAZZ Way
Start to check serial...
!! UpgClientTest FAIL: RSP error!!
P UPGOOOTAGE P2P UPG

what am I doing wrong
I wanted to load v580

Please reset the STB!
BOOTROM ...
UPG...
DDR Calibration Completed
start send upgclient
Start to check serial...
!! UpgClientTest FAIL: Receive failed !!
Please reset the STB!

gosiadila1234
Posts: 8
Joined: Thu Dec 07, 2017 12:10 pm

Re: rs 232

Post by gosiadila1234 »

does it mean that you can not go back to older software

User avatar
Feralkiwi
网站管理员
Posts: 8341
Joined: Fri Aug 12, 2016 6:51 am
Location: New Zealand

Re: rs 232

Post by Feralkiwi »

Please have a read of my comments on this subject here.
The relevant section is well down.
It looked like I needed to load a much older version and then upgrade via USB.

Owen
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.

gosiadila1234
Posts: 8
Joined: Thu Dec 07, 2017 12:10 pm

Re: rs 232

Post by gosiadila1234 »

Sorry I forgot to write that this is v8 super. I use the CH341 adapter for USB for a laptop, i.e. 5V from the USB port. Maybe the low voltage on rs232 CH341 causes errors and the software does not want to load either from pendriva or from rs232.
My software version S / W V4.5.118.626 20/11/2017, H / W V1.2.0 08/08/1015
Is the software guilty? or USB / RS232 for low voltage?
Maybe try on a laptop with rs232?

The only software that the decoder takes is a v625 with USB .... with rs232 does not want to program

On another laptop with VISTA it did not connect at all.

User avatar
Feralkiwi
网站管理员
Posts: 8341
Joined: Fri Aug 12, 2016 6:51 am
Location: New Zealand

Re: rs 232

Post by Feralkiwi »

Try a much older version of the software via RS232.

I found I could downgrade far back and then upgrade again.

Owen
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.

gosiadila1234
Posts: 8
Joined: Thu Dec 07, 2017 12:10 pm

Re: rs 232

Post by gosiadila1234 »

I tried all available on the forum - no one wants to load
If You have an elderly at home, please send it to me.
I read all threads from rs232 and came to the conclusion that there are two possibilities either USB-RS232 gives too low voltage (5V) or the decoder has some error
Only flash.bin (V625) pendriva loads and rs232 does not want to load the software.
I checked USB-RS232 on other ariwa, globo decoders and works without any problem.

gosiadila1234
Posts: 8
Joined: Thu Dec 07, 2017 12:10 pm

Re: rs 232

Post by gosiadila1234 »

I found a solution ... Old computer with full rs232 DE-9 The first time Tcom-UPG connected to the decoder and loaded the flash v580.
The conclusion is that not every USB-RS232 is a good solution. The V8 needs a lot
full RS-232 DE9, then there is no problem with loading older software.
Thank you for your interest, others will be a hint as to the problem with the RS232 connection

Nibret
Posts: 57
Joined: Thu Sep 28, 2017 9:33 pm

Re: rs 232

Post by Nibret »

Do you mean that I have to install xp instead of wondows 10 pro on my core i7, 1tb laptop?
I have full bothe sides female end rs232 def 9 cable,
And modified tx-dx, dx_tx and ground-ground (three wires) coonection male_female end cables. Both are not functional on Windows10 pro latest version.
So I need your advise soon pls.

gosiadila1234
Posts: 8
Joined: Thu Dec 07, 2017 12:10 pm

Re: rs 232

Post by gosiadila1234 »

I've been using an old computer for 10 years with XP and for the first time
connected with the V8 super.
Other ariva, globo, vu decoders worked on the USB / RS232 CH340 adapter but Freesata revived the old computer with the original rs232. D-9
With the Win 7 64 bit laptop the program did not want to load the software.

tanka
Posts: 481
Joined: Sun Aug 21, 2016 4:35 pm

Re: rs 232

Post by tanka »

Same here I use one old computer with XP to fix V8 super and same more receivers. The new computer and windows 10 not working

gosiadila1234
Posts: 8
Joined: Thu Dec 07, 2017 12:10 pm

Re: rs 232

Post by gosiadila1234 »

I'm going to buy a docking station, I have a Dell PR02X Latitude Precision laptop
so cheaper will go out than a good USB / RS232 adapter and you do not have to take out your old computer.
I also checked the connection and programming on the IP network with the PC update Tool Tool_v2 ... program very nicely.

Post Reply

Return to “GTMEDIA V8 SERIES”