POWERVU - CANNOT ADD NEW NUMBERS
Moderators: admin, GTMedia Team
-
- Posts: 25
- Joined: Sun Jun 24, 2018 9:23 pm
- Location: Texas, USA
POWERVU - CANNOT ADD NEW NUMBERS
I am using a FREESAST V8 SUPER. Need to add new POWERVU numbers - but - receiver does not allow me to access "CONDITIONAL ACCESS". Do I need to be in a special area using the remote? Any help would be appreciated.
Re: POWERVU - CANNOT ADD NEW NUMBERS
nanirdjeff1937 wrote:I am using a FREESAST V8 SUPER. Need to add new POWERVU numbers - but - receiver does not allow me to access "CONDITIONAL ACCESS". Do I need to be in a special area using the remote? Any help would be appreciated.
- Attachments
-
- 20180904_163539.jpg (318.45 KiB) Viewed 2206 times
-
- Posts: 25
- Joined: Sun Jun 24, 2018 9:23 pm
- Location: Texas, USA
Re: POWERVU - CANNOT ADD NEW NUMBERS
I thank you for the POWERVU keys. However, I have a question - on the grid it gives the following information - CIAD, PROV, IDX and KEYDATA.
I cannot change or add any thing to the CIAD - should I be able to?
What do I add/change in PROV?
IDX I have reasoned is where the "0" and the "1" goes - is this correct?
And the numbers that have been suplied go to - KEYDATA
My Freesat V8 Super receiver does not appear to have the POWERVU PROGRAM loaded. My Freesat V7 automatically loads the program when you re-start the receiver - gives information as to the LAN connection and the POWERVU information, which ends in ????? 3 - and it does this automatically each time the receiver is disconnected or shut down. The V8 only shows that the LAN connection is connected, and there is no mention of POWERVU.
How do I get this POWERVU program to load?
I thank you for your time and help in this matter.
I cannot change or add any thing to the CIAD - should I be able to?
What do I add/change in PROV?
IDX I have reasoned is where the "0" and the "1" goes - is this correct?
And the numbers that have been suplied go to - KEYDATA
My Freesat V8 Super receiver does not appear to have the POWERVU PROGRAM loaded. My Freesat V7 automatically loads the program when you re-start the receiver - gives information as to the LAN connection and the POWERVU information, which ends in ????? 3 - and it does this automatically each time the receiver is disconnected or shut down. The V8 only shows that the LAN connection is connected, and there is no mention of POWERVU.
How do I get this POWERVU program to load?
I thank you for your time and help in this matter.
Re: POWERVU - CANNOT ADD NEW NUMBERS
Please look at these instructions on Powervu entry.
As for the Caid. This does not need changing as if you are entering a Powervu code the Caid is for that channel's powervu.
Owen
As for the Caid. This does not need changing as if you are entering a Powervu code the Caid is for that channel's powervu.
Owen
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.
-
- Posts: 25
- Joined: Sun Jun 24, 2018 9:23 pm
- Location: Texas, USA
Re: POWERVU - CANNOT ADD NEW NUMBERS
Thank you feralkiwi for this information - will proceed accordingly.
Re: POWERVU - CANNOT ADD NEW NUMBERS
Maybe is easier to upload a softcam key file, isn't it?nanirdjeff1937 wrote:Thank you feralkiwi for this information - will proceed accordingly.