I have a freesat v7 hd.
My problem is that the box has problems changing the satellite.
I have 58w, 40w, 30w and 97w
with four antennas.
All the satellites look good if I put them directly to the box.
if I put them with a switch, it only lets me see the 40w that is circular.
The switch and cables are fine.
I have more than one switch.
one 4 x 1 and another 8 x 1 /
with the two switches it does the same ..
Will the box be damaged?
Or it is something else.
Tengo un freesat v7 hd.
Mi problema es que la caja tiene problemas para cambiar el satélite.
Tengo 58w, 40w, 30w y 97w
con cuatro antenas.
Todos los satélites se ven bien si los pongo directamente en la caja.
si los pongo con un interruptor, solo me deja ver el 40w que es circular.
El switch y los cables están bien.
Tengo más de un interruptor
uno 4 x 1 y otro 8 x 1 /
con los dos interruptores hace lo mismo ...
¿Se dañará la caja?
O es algo más.
Question my freesat v7 hd is being damaged ?
Moderators: admin, GTMedia Team
Question my freesat v7 hd is being damaged ?
La mente es como un paracaídas, no sirve si no se abre...
Re: Question my freesat v7 hd is being damaged ?
Buena pregunta.
Deberías si tienes un tester o multimeter de chequear la salida de voltaje en lnb in y si pasa voltaje suficiente cuando cambias de horizontal a vertical
A mi se me hace que los multi switch están kk
Me ha pasado y terco nunca cambio es que conecto y desconecto el coaxial sin apagar el receiver. No hagan eso nunca. Yo si jejeje
La otra cosa habría que ver el seteado que tienes mayormente que lnb power este en auto
Deberías si tienes un tester o multimeter de chequear la salida de voltaje en lnb in y si pasa voltaje suficiente cuando cambias de horizontal a vertical
A mi se me hace que los multi switch están kk
Me ha pasado y terco nunca cambio es que conecto y desconecto el coaxial sin apagar el receiver. No hagan eso nunca. Yo si jejeje
La otra cosa habría que ver el seteado que tienes mayormente que lnb power este en auto
Re: Question my freesat v7 hd is being damaged ?
Debes de empezar verificando la configuracion de los Swich, verifica el voltaje de salida hacia el NLB.
Randsur
Re: Question my freesat v7 hd is being damaged ?
I have had this problem with many of Freesat's units.
The issue is the LNB power over current protection.
With a 8x1 DiSEqC 1.1 and a 4x1 DiSEqC 1.0 switch, I find that when the second switch and LNB power on the over current trips in and cuts the power for a moment.
This resets the 8x1 switch (the uncommitted switch) to port 1.
To stop this I have a signal splitter in the LNB cable at the set top box.
This provides some impedance to the circuit and stops this.
You can use a tone sat find too.
There are some of my comments and finding here.
Owen
The issue is the LNB power over current protection.
With a 8x1 DiSEqC 1.1 and a 4x1 DiSEqC 1.0 switch, I find that when the second switch and LNB power on the over current trips in and cuts the power for a moment.
This resets the 8x1 switch (the uncommitted switch) to port 1.
To stop this I have a signal splitter in the LNB cable at the set top box.
This provides some impedance to the circuit and stops this.
You can use a tone sat find too.
There are some of my comments and finding here.
Owen
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.
Re: Question my freesat v7 hd is being damaged ?
It may or maybe not.Feralkiwi wrote:I have had this problem with many of Freesat's units.
The issue is the LNB power over current protection.
With a 8x1 DiSEqC 1.1 and a 4x1 DiSEqC 1.0 switch, I find that when the second switch and LNB power on the over current trips in and cuts the power for a moment.
This resets the 8x1 switch (the uncommitted switch) to port 1.
To stop this I have a signal splitter in the LNB cable at the set top box.
This provides some impedance to the circuit and stops this.
You can use a tone sat find too.
There are some of my comments and finding here.
Owen
I did had the same issue. It came out it was the switch, twice
My configuration is atypical and it's been a year so far so good.
2 V8 Super (family room and master bedroom)
1 - 8' with 3 LNB 2 outputs each (C linear, C circular and Ku) from 40.5 to 135W
1 76cm Dish Circular Ku fixed for 77W 2 outputs
1 76 cm Universal Ku for 30W 2 outputs
1 OTA for local channels 2 outputs
Each output goes to two different multiswitch that I brought from Europe brand Centauri
So I am using on each multiswitch 5 ports Pus the OT still 3 left
Never had an issue, however with those 4 x 1 man..... pain in the @ss, exactly what you are experiencing
---------
So summury
Do this to find out if it is the switch or something else
1) check the signal on all 4 dishes and that you can watch.
2) connect the multiswitch ANY BUT just ONE dish at port 1
3) The move it at port 2 and so on. That you will see if all ports are working. remember to change the settings on the V7 to each port
If one port (at least is not working) get another switch. If it works got to next step
4) Now leave that dish on port 1 and add the second dish on port 4. see what happens.
5) Switch dishes and see which one fails.
Hope it helps
Si necesitas mas ayuda estoy a tu disposicion
Re: Question my freesat v7 hd is being damaged ?
Thanks for your comments.
Very interesting all
the configuration is fine.
I put the satellites from largest to smallest.
30w in port 1, 40w in port 2, 58w in port 3.
not to be wrong
interesting that of using spliter.
For the moment, I'm going to try using a jynxbox 30 to get rid of doubts.
Then I follow your advice.
All very good.
Thank you.
Gracias por sus comentarios.
Muy interesantes todos
si estoy revisando la configuracion.
pongo los satelites de mayor a menor.
30w en el puerto 1,el 40w en el puerto 2, el 58w en el puerto 3.
para no equivocarme.
interesante ese de usar spliter.
Por el momento, voy a probar usando una jynxbox 30 para salir de dudas.
Luego sigo sus consejos.
Todos muy buenos.
gracias.
Very interesting all
the configuration is fine.
I put the satellites from largest to smallest.
30w in port 1, 40w in port 2, 58w in port 3.
not to be wrong
interesting that of using spliter.
For the moment, I'm going to try using a jynxbox 30 to get rid of doubts.
Then I follow your advice.
All very good.
Thank you.
Gracias por sus comentarios.
Muy interesantes todos
si estoy revisando la configuracion.
pongo los satelites de mayor a menor.
30w en el puerto 1,el 40w en el puerto 2, el 58w en el puerto 3.
para no equivocarme.
interesante ese de usar spliter.
Por el momento, voy a probar usando una jynxbox 30 para salir de dudas.
Luego sigo sus consejos.
Todos muy buenos.
gracias.
La mente es como un paracaídas, no sirve si no se abre...
Re: Question my freesat v7 hd is being damaged ?
ok
Let us know the outcome so we go further from here
Let us know the outcome so we go further from here
Re: Question my freesat v7 hd is being damaged ?
I do not know what happened, but the box was fixed.
Check all the cables and I put it
adhesive tape on the connectors.
I improve the change of satellites a lot.
Still sometimes it flashes when changing satellites. Especially when I change to a 40w channel that is circular.
But I can live with that delay of a few seconds.
Maybe some cable picked up moisture.
It is what I imagine.
No se bien que paso ,pero se arreglo la caja.
Revise todos los cables y le puse
cinta adesiva en los conectores.
Mejoro mucho el cambio de satelites.
Todavia a veces parpadea al cambiar de satelites . En especial cuando cambio a un canal del 40w que es circular.
Pero puedo vivir con ese retraso de unos segundos.
Quizas algun cable cogio humedad.
Es lo que me imagino.
Check all the cables and I put it
adhesive tape on the connectors.
I improve the change of satellites a lot.
Still sometimes it flashes when changing satellites. Especially when I change to a 40w channel that is circular.
But I can live with that delay of a few seconds.
Maybe some cable picked up moisture.
It is what I imagine.
No se bien que paso ,pero se arreglo la caja.
Revise todos los cables y le puse
cinta adesiva en los conectores.
Mejoro mucho el cambio de satelites.
Todavia a veces parpadea al cambiar de satelites . En especial cuando cambio a un canal del 40w que es circular.
Pero puedo vivir con ese retraso de unos segundos.
Quizas algun cable cogio humedad.
Es lo que me imagino.
La mente es como un paracaídas, no sirve si no se abre...
Re: Question my freesat v7 hd is being damaged ?
Feralkiwi wrote:I have had this problem with many of Freesat's units.
The issue is the LNB power over current protection.
With a 8x1 DiSEqC 1.1 and a 4x1 DiSEqC 1.0 switch, I find that when the second switch and LNB power on the over current trips in and cuts the power for a moment.
This resets the 8x1 switch (the uncommitted switch) to port 1.
To stop this I have a signal splitter in the LNB cable at the set top box.
This provides some impedance to the circuit and stops this.
You can use a tone sat find too.
There are some of my comments and finding here.
Owen
The box failed me again.
The solution is this. Thank you.Feralkiwi
I am using a finder.
all good/
La mente es como un paracaídas, no sirve si no se abre...